Omni Lighted Nocks......When???? Flat Nock Replacement ????

Discussion in 'TenPoint Crossbows' started by NDPronghorn, May 22, 2013.

  1. NDPronghorn

    NDPronghorn Member

    Messages:
    174
    Likes Received:
    29
    Is Tenpoint planning to get into the lighted nock business and if so when?? Would like to know their plans plus what is their actual recommendation to remove existing flat nocks and install Omni's without damaging the arrows and then re-seating the Omni's to accurately align with the existing vanes? Would like to shoot Omni's (preferably lighted) out of my XLT as well as the new Vapor.
     
  2. ghostgoblin22

    ghostgoblin22 Active Member

    Messages:
    1,183
    Likes Received:
    517
    they will, the more demand, it will come sooner, i you want all your arrows in omni nock go to south shore archery supply, they will hook you up, ive been shooting flat nocks just as good on my bow so ill be buying lumenoks soon
     
  3. 10PtCrossbow

    10PtCrossbow TenPoint Representative

    Messages:
    1,192
    Likes Received:
    620
    ND,
    TenPoint is not planning on getting into the lighted nock business, but we are working with several companies that are. I suspect there will be an option or two before the fall hunting season.
     
  4. allchokedup

    allchokedup Active Member

    Messages:
    1,905
    Likes Received:
    747
    Location:
    Upper Middle, TN
    Hi NDPronghorn,

    I recently replaced the flat nocks with Omni nocks. I removed the flat nocks out of a dozen Pro Elites.
    I only installed 6 arrows with the Omni nocks and I'm saving the other T.P. Pro Elites for the lighted version when they come up for sale. It was a little hard removing the flat nocks, even after placing them under hot water. Some came out fairly easy, but a few were really glued in good. I drilled a small hole in the end of the nock and installed a screw in the hole. Reheated it up under hot water and pulled like heck on the screw. Wha-lah, done! When you purchase a pack of 12 Omni nocks an alignment tool comes with it. I used a 2 part epoxy to install the Omni's because it has a slow set time to allow you to align them with your vanes. Make sure you clean the inside of the shaft and nock before installation. I used some sand paper on the inside of the shaft and used Acetone to clean the inside of the shaft and the end of the Omni nock. Alcohol should work too. Its a real easy job to install them and you will like the Omni nocks.
    Good luck, David
     
  5. 10PtCrossbow

    10PtCrossbow TenPoint Representative

    Messages:
    1,192
    Likes Received:
    620
    I saw some good things with the lighted Omni nock. We are making prgress. More details in the next few weeks.
     
  6. deercamp

    deercamp New Member

    Messages:
    23
    Likes Received:
    0
    Any updates on the lighted Omni's?
     
  7. 10PtCrossbow

    10PtCrossbow TenPoint Representative

    Messages:
    1,192
    Likes Received:
    620
    Deer,
    I will see if I can get an update tomorrow.
     
  8. allchokedup

    allchokedup Active Member

    Messages:
    1,905
    Likes Received:
    747
    Location:
    Upper Middle, TN
    I've got some arrows ready and waiting for the lighted Omni's.
    Thanks Randy
     
  9. 10PtCrossbow

    10PtCrossbow TenPoint Representative

    Messages:
    1,192
    Likes Received:
    620
    I just talked to engineering and they still don't have an ETA for me. Sorry.
     
  10. Bluescab05

    Bluescab05 New Member

    Messages:
    73
    Likes Received:
    18
    Just got an email by the folks at Lumenock. They pretty much said they are waiting for permission from the paten holder to start making them.
     
  11. highoctane

    highoctane Active Member

    Messages:
    439
    Likes Received:
    303
    Location:
    SC
    That sounds like another way to "pass the buck"....
     
  12. 10PtCrossbow

    10PtCrossbow TenPoint Representative

    Messages:
    1,192
    Likes Received:
    620
    I just spoke with the engineers and it looks like we will have lighted Omni nocks in mid September. The first ones will be for a .297 inside diameter shaft.
     
  13. Laelkhunter

    Laelkhunter New Member

    Messages:
    67
    Likes Received:
    12
    Please pardon my ignorance- Is that the inside diameter of the Aluminum or Carbon shaft? All of my bolts are WR Aluminum 2219..
     
  14. allchokedup

    allchokedup Active Member

    Messages:
    1,905
    Likes Received:
    747
    Location:
    Upper Middle, TN
    I believe it is the Tenpoint carbon Pro Elites. Inside measurement .297.
     
  15. Laelkhunter

    Laelkhunter New Member

    Messages:
    67
    Likes Received:
    12
    Thank you. Still trying to learn
     
  16. 10PtCrossbow

    10PtCrossbow TenPoint Representative

    Messages:
    1,192
    Likes Received:
    620
    Pro Elite and Pro V 22 arrows with the new lighted Omni nock will start shipping September 30th.
     
  17. 10PtCrossbow

    10PtCrossbow TenPoint Representative

    Messages:
    1,192
    Likes Received:
    620
    Here is a picture of the nock lit and unlit. What is really neat, but the pictures don't show, is the way it indexes properly every time. No more mis-aligned nocks after turning them off and on!
     

    Attached Files:

  18. bobbyd1947

    bobbyd1947 Well-Known Member

    Messages:
    5,161
    Likes Received:
    2,776
    Randy how do you turn them off?
     
  19. 10PtCrossbow

    10PtCrossbow TenPoint Representative

    Messages:
    1,192
    Likes Received:
    620
    Pull the nock back out.
     
  20. jdhaines32

    jdhaines32 Member

    Messages:
    161
    Likes Received:
    33
    Location:
    Pa.
    Are these being made by Ten Point or are they made by another lighted nock company?
     

Share This Page