Sling Carry....

Discussion in 'TenPoint Crossbows' started by AlexG., Oct 9, 2009.

  1. AlexG.

    AlexG. Senior Member

    Messages:
    131
    Likes Received:
    3
    Location:
    Virginia Beach, Va.
    I posted this same question(post on the TenPoint site, but wanted to get opinions from here as well.
    Okay, so this season is my first with my Titan HLX and for that matter carrying a xbow into the woods. My question is about carrying methods.
    What is the normal method for carrying your xbow into the woods? I have a sling on mine but have noticed that with the quiver attached I cannot carry the xbow with the limbs up, because the sling interferes with the arrows in the quiver. So I have to carry it with the limbs facing down. Without the quiver installed then its not a problem and I can carry it right side up.... but that sort of defeats the purpose of having the quiver mount now doesnt it?

    Thanks
    Alex
     
  2. coyote170

    coyote170 Banned

    Messages:
    258
    Likes Received:
    6
    Check with Moon he has the solution to your problem!
     
  3. AlexG.

    AlexG. Senior Member

    Messages:
    131
    Likes Received:
    3
    Location:
    Virginia Beach, Va.
    Yep... I saw Moon's set up thanks
     
  4. sandbur

    sandbur New Member

    Messages:
    8
    Likes Received:
    0
    Newbie here, and I am trying to find moon's solution or if anyone else has new ideas.
     
  5. Moon

    Moon Senior Member

    Messages:
    4,270
    Likes Received:
    87
    A couple photos showing where the rear stud is mounted for carrying the crossbow in bow down position. Makes carrying crossbows a breeze. Leave the front stud where it is.
    I'm also posting a photo of an older Ten Point showing where I mount the quiver using the Kwikee Hi Riser bracket and 3 arrow quiver. Required drilling 2 small holes in the thick webbing of the riser. I'm also working on a bottom mount using the factory quiver mounting holes.
     

    Attached Files:

  6. sandbur

    sandbur New Member

    Messages:
    8
    Likes Received:
    0
    Thank you , moon. The help is very much appreciated!
     
  7. agingcrossbower

    agingcrossbower advanced member

    Messages:
    669
    Likes Received:
    472
    Location:
    East Central Wi.
    Yes, Moon thanks for posting your idea's. :thumbsu:
     
  8. Elkhunter1

    Elkhunter1 New Member

    Messages:
    138
    Likes Received:
    0
    Location:
    Gentry, Arkansas
    Make it three moon. great ideas. I will be changing my tenpoint oven when it comes back for summer PM's
    Jim
     
  9. Moon

    Moon Senior Member

    Messages:
    4,270
    Likes Received:
    87
    I've been ribbed by a certain gentleman ( I tend to use the term loosely :p )at Ten Point about drilling holes in crossbows. I can't help it. If Ten Point would put those holes in the right place, I could put my drill away. :D Only kidding. Great folks and great crossbows for sure.
     
  10. mopar1969

    mopar1969 Senior Member

    Messages:
    724
    Likes Received:
    6

    Does'nt the string hit the riser bracket when you fire?
     
  11. Moon

    Moon Senior Member

    Messages:
    4,270
    Likes Received:
    87
    For some crossbows, a 3/16" thick aluminum spacer plate will be needed to raise the bracket out of the string's path. A hack saw, drill and file is all that is needed......other than the aluminum, which can be purchased at Home Depot or Lowes.
     

Share This Page